The Classic Style In Parking

Horizontal parking on upper and lower level.
The Liftparker emphasizes conveniences

Installation in the carport with Outdoorpaker.
The platforms have to be forward brought in accordance with operating instructions.

Features & Options

Horizontal parking on upper and lower level. The Liftparker emphasizes conveniences.
Scope of supply / Options

Features of the Liftparker N 4400 E/D

- Key switch incl. emergency stop, dead man's control type with brief operating instructions and wiring to aggregate
- "lockable key switch" - Key is extractable from switch only when the installation is lifted.
- s/d-installation with 2 platforms, 2 column assemblies c/w hydraulic cylinder, lifting carriage and hydraulic unit.
- Width of lot 230cm and depth of pit 170/165 cm as standard
- Width of lot modified to 240cm and wider or PD 185/180 and deeper recommended for higher car accessibility and conveniences synchronizing device to improve operation with unequal load distribution entering wedge for car positioning.
- Safety device to prevent from lowering in case of pipe fracture

- Mounting on installation and aggregate with HD-anchors, wiring with impact dowels
- Bonded anchors for increased foundation requirements

- Drive unit "Silencio" with tubing and wiring to the installation
- Hydraulic package "parallel operation": simultaneous lifting of 2 or more installations per aggregate at given pump capacity, or simultaneous lowering respectively
- Structure-borne noise package to comply with DIN 4109 and adherence to sound insulation measure Rw '55
- Sound insulation hood to minimize airborne sound
- HVLP-oil for excessive fluctuations in temperature

- Drive plates in trapezoid style sheeting
- Rubber profiles in the pedestrian area, width 40cm or 60cm, in the pedestrian and drive area 60cm and 40cm
- Luxury sheet metal only for horizontal lots

- Corrosive prevention "Classic" of drive plates by continuous line-galvanizing to DIN EN 10142/10143
- Corrosion prevention "Premium" of drive plates by individual piece-galvanizing to DIN ISO 1461
- Corrosion prevention "Classic Plus" of drive plates by line-galvanizing to DIN EN 10142/10143 and coating of the top surfaces Corrosion prevention "Premium Plus" of the driving plates by individual piece-galvanizing to DIN ISO 1461 and coating of the top surfaces

- Railings to avoid risk of falling onto the platform, insofar as necessary
(Note: Safe guarding against shearing and squeezing have priority and must be provided by the proprietor)

- Ramps when door facing is not available to install the door slide rail, pit length must be 525cm, at the minimum
- Vehicle load: 2,0 to, length: 5m, as per vehicle data
- Extra capacity of upper platform to 2,5 to, vehicle length up to 5,20m

- A maintenance contract is recommended
- Attendance and cleaning to require ments or at regular intervals is recommended

Intersections/Customer's Duties

- Lockable main switch, near to aggregate, completed at the beginning of erection
- Capacity of the aggregate: 400V, 50Hz, three phrase motor 3,0kw Supply line to main switch 5 x 1,5mm2 or to local regulations, fuse protection 3 x 16 amp, slow fuse Level surface (L x W) 50cm x 20cm to attach the control unit, adjacent to the installation, outside the operational platform area
- Safeguarding to DIN EN 294
- Lighting to DIN 67528, illumination of parking lots and buildings for parking
- Foundation exactly to size, clean and dry
- Compliance with installation requirements as per quotation
- The measurements are minimum finished dimensions.
- Tolerances to VOB part C (DIN 18330, 18331) should be considered supplementary.
Measurements in cm.

Technical alterations reserved. Alterations in the scope of supply reserved. Version 14/2002

	Foundation Plan: The pit must be executed in compliance with the designated forces. All forces are led into the ground via bearing plates of a minimum area 150cm2. The bearing plates are fixed with metal straddling dowels. The drill hole depth is approx. ca. 14cm. All walls in the pit below the entrance level must be of concrete.
	Fahrzeugdaten Gewicht: max. 2000kg, Radlast max 500kg Platform oben und unten: Pkw-Hohe H Optional: Version S-Klasse, Fahrzeuglange 510cm Gewicht: max 2500kg, Radlast max. 625kg Nur auf E-Anlage oben, Stellplatzbreite S = 250/260/270cm Anlagenbreite B = 280/290/300cm Grubenlange: 540cm.

Measurements, Engineering & Design

The CLASSIC STYLE in PARKING: Liftparker N4400 E/D
Horizontal parking on upper and lower level. The Liftparker emphasizes conveniences