The Classic Style In Parking

Independent parking on 2 levels on the entrance level with sliding platforms and one empty space, on top with horizontal movable platforms. With low requirements on the ground-surface.

Features & Options

*Scope of supply
* Options

Features of the Uniparker

*Control element incl. emergency stop in automatic-control with brief operating instructions and wiring to switch cabinet.
*"Lockable key switch" Key is extractable only when the gate is closed
*installation with sliding platforms and one empty space on the entrance level and movable platforms on the level below. Complete with hydraulic drive elements and electrical control.
*Width of lot 230cm and depth of pit 175 cm as standard
*Width of lot modified 240cm and wider with depth of pit modified 200 recommended for higher conveniences
*Mono-hub cylinder to drive the horizontal movable platforms with looped-around suspension elements, sliding platforms with electrical drive
*entering wedge for car positioning.
*Safety device to prevent kneeling by leakage, pipe burst, fracture of suspension elements.

*Mounting of installation and aggregate with HD-anchors, electrical wiring with impact dowels
*Bounded anchors for increased foundation requirements

*Drive unit 'Silencio' with tubing and wiring to the installation
*Structure-borne noise package to comply with DIN 4109 and adherence to sound insulation measure Rw 55
*Sound insulation hood to minimize airborne sound
*HVLP-OI for excessive fluctuations in temperature

*Drive plates in trapezoid style sheeting
*Rubber profiles in the pedestrian area, width 40cm or 60cm, in pedestrian and drive area 60cm and 40cm
*Luxury sheet metal

*Corrosion prevention "Classic" of drive plates by continuous line-galvanizing to DIN EN 10142/10143
*Corrosion prevention "Premium" of drive plates by individual piece-galvanizing to DIN ISO 1461
**Corrosion prevention "Classic Plus" of drive plates by line-galvanizing to DIN EN 10142/10143 and coating of the top surfaces (dependent on the market needs the scope of supply contains zinc and powder coated sheet metal)
*Corrosion prevention "Premium Plus" of the drive plates by individual piece-galvanizing to DIN ISO 1461 and coating of the top surfaces

*Sliding doors for fall-danger prevention into the pit and railings from the platform (Notice: safe guarding against shearing and squeezing have priority and must provided by the proprietor sideways and behind the installation)
*Remote control and/or automatic-drive for sliding doors
*Modem for teleservice for online-analysis and help
*Assembly of the ramp behind the columns, length of pit must have at least 560cm
*Vehicle load 2,0 to 5m length according to vehicle data
Extra capacity of upper platform to 2,5 to, vehicle length till 5,10m, length of pit plus 10 cm
*A maintenance contract is recommended

Intersections/ Customer's duties

• Aggregate power: 400V, 50Hz, three-phase motor, 3,0Kw, assembly in pit range or in direct near of the system, LBH ca 60 x 22 x 40 cm
• Supply line to switch cabinet 5x 1,5mm2, or to local regulations, fuse protection 3 x 16amp, slow fuse
• Electrical potential equalisation (foundation ground stell-construction to VDE 0100 T410)
•Telephone line dto by option modem and teleservice, after consultation
• Free space for switch cabinet LBH ca 60 x 22 x 80cm, with swing door in immediate near to installation (max 6m) with access to the parking system
• Level surface HxB 50cm x 20cm to attach the control unit in direct near of the installation
• Safeguarding to DIN EN 294
• Lighting to DIN67528, illumination of parking lots and buildings for parking
• Foundation exactly to size, clean and dry
• Compliance with installation requirements as per quotation The measurements are minimum finished dimensions. Tolerances to VOB part C (DIN 18330, 18331) should be considered supplementary. Measurements in cm.

Technical alterations reserved, alterations in the scope of supply reserved. Version 15/2004

	Vehicle data (profile as on top) Weight: max. 2000kg, wheel load max 500kg Vehicle height H according table
	Option: Version S-class, vehicle length 510cm Only on the top spaces Weight: max 2500kg, wheel load max. 625kg Width of space S = 250cm Raster width B1 = 280cm, B2 = 270cm Pit length: 570cm

Layout Gates, mounting of the gates max, 210cm inside height
Layout A: sliding door's between pillars.
Columns supplied by the employer min. each 2 segments, otherwise assembly of the gates in front of pillars
Layout B: sliding doors in front of pillars
Layout C:sliding doors behind pillars
on gate outlet supplied by the employer, pit must be shown behind the gate outlet, the allowed pit length of 560cm